Who this service is for
This page is for project work, not a one-off repair. Typical requests:
- General contractors who need a plumbing sub for a finish-out, a remodel or a ground-up building.
- Developers and owners turning a shell or a second-generation space into something new.
- Restaurant operators moving into a space that needs a kitchen, floor drains and a grease interceptor.
- Medical and dental tenants whose buildout includes medical gas piping.
- Property managers doing a white box, a restroom upgrade or a common-area renovation.
If you only need something fixed, a service call is usually the better fit. See restaurant plumbing for kitchens that are already open.
Signs the job needs a plumbing contractor
A service call fixes what is there. A contractor changes what is there. You are in contractor territory when:
- Fixtures move or multiply. New restrooms, a relocated break room or a different fixture count means new drain, vent and supply lines.
- A kitchen is going in. In Dallas, any commercial or institutional food service needs a grease trap, sized under the Dallas Plumbing Code. The city points sizing questions to its Plumbing and Mechanical Section.
- A backflow assembly is new or moved. TCEQ rules require every backflow prevention assembly to be tested when it is installed.
- Medical gas is on the drawings. In Texas, medical gas piping takes a separate endorsement, and the work runs under a Responsible Master Plumber who also holds it.
- The water heater plan changes. A new tenant use often needs a different size or type of unit.
What is involved
Most commercial plumbing projects follow the same five steps.
- Scope review. The pro reads the drawings or your written scope, flags gaps, and lists exclusions.
- Site walk and bid. They check existing lines, the tie-in points, slab and ceiling access, and the schedule. Then they price it in writing.
- Rough-in and inspections. Underground and in-wall piping goes in, gets tested and gets inspected before walls close.
- Trim and equipment. Fixtures, water heaters, grease interceptors and backflow assemblies get set and connected.
- Testing and closeout. In Dallas, backflow tests tied to a permit are now filed by the tester through SwiftComply. Since September 25, 2026, Dallas Water Utilities reviews those reports and passes approved ones to the Planning and Development Department under the permit number. The permit's primary contact gets an email through the DallasNow system confirming the test passed.
Cost of commercial plumbing contractor work
Finish-out and new construction are bid per project, so there is no honest single range. The rates below help you read a bid or a time-and-materials ticket. They are national figures from cost guides, and the real number comes from an on-site look.
| Item | Reported range | Source |
|---|---|---|
| Commercial plumbing company rate | About $100 per hour | Angi plumbing cost guide |
| Journeyman plumber rate | $60 to $110 per hour | Angi plumbing cost guide |
| Master plumber rate | $80 to $200 per hour | Angi plumbing cost guide |
| Commercial water heater, unit and install | $2,500 to $4,500 | hotwater.com cost guide |
| New commercial RPZ backflow test | $95 to $300 per device | FindBackflowTesters cost guide |
See the commercial plumbing cost page for how bids are built and how to compare them.
What to ask a commercial plumbing contractor
Before you award the job, get straight answers to these:
- Who is the Responsible Master Plumber? The Texas State Board of Plumbing Examiners says a company offering plumbing to the public must have at least one, plus a current certificate of insurance on file with the board. Get the name and license number and check the list.
- Who pulls the plumbing permit and books inspections? Put it in the contract.
- What is excluded? Grease interceptors, water heaters, backflow assemblies, gas piping and core drilling are common gaps between trades.
- How many people, and when? Ask for crew size at rough-in and trim, and lead times on long-lead equipment.
- How are change orders priced? Hourly rate, markup on material, and who approves.
- Who tests the backflow assembly? It takes a TCEQ-licensed tester, and in Dallas the tester must be registered with the city. If the job includes a fire line assembly, TCEQ allows a tester to work on fire lines only when permanently employed by an Approved Fireline Contractor.
Need testing on an existing building instead? Go to backflow testing.
Areas we cover for commercial plumbing contractors
Frequently asked
Can I send plans through the form?
Describe the project in the form: the address, the use, the square footage, and whether drawings exist. The pro you are matched with will tell you how to get the plan set to them for a bid.
Do you match plumbing subs for ground-up commercial buildings?
Yes, as well as finish-outs and remodels. Say which it is in the form, along with the start date and the phase you are in, so the pro knows what they are bidding.
Why does the bid list exclusions?
Because plumbing scopes overlap with other trades. A clear list of what is not included, like core drilling, gas piping or the grease interceptor itself, keeps two subs from both assuming the other one has it.
Is a journeyman allowed to run my job?
A journeyman can install and repair plumbing in Texas, but under the supervision of a Responsible Master Plumber. Ask who that is for your project.